Application Notes and User Manuals

The Application Notes are stored in PDF format. To view them you will need Acrobat Reader Version 3.0 or later. This is available from Adobe free of charge for several different platforms.

Click here to get the Reader

Available Application Notes


Available Manuals

App NoteAN50601 In-System Programming of ST7 Microcontrollers

This application note describes how ST7 Microcontrollers may be programmed in-circuit using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN50601 (214 Kbytes)

App NoteAN30701 In-System Programming of EPCS1/4

This application note describes how the EPCS1/4 serial configuration devices may be programmed in-circuit using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN30701 (207 Kbytes)

App NoteAN30901 In-System Programming of MICROWIRE Devices

This application note describes how 93xxx / 59xxx devices may be programmed in-circuit using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN30901 (201 Kbytes)

App NoteAN30702 In-System Programming of M25Pxxx

This application note describes how the ST Serial Flash M25Pxxx devices may be programmed in-circuit using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN30702 (199 Kbytes)

App NoteAN30201 In-System Programming of ST Flash PSDs

This application note describes how the ST Flash PSD family devices may be programmed in-circuit using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN30201 (139 Kbytes)

App NoteAN20201 In-System Programming of I˛C E˛PROMS

This application note describes how the 24Cxx Family of E²PROM devices from various manufacturers may be programmed in-circuit using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN20201 (232 Kbytes)

App NoteAN80501 In-System Programming of Logic Devices

This application note describes how a wide range of logic devices from various manufacturers may be programmed in-circuit using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN80501 (31,010 bytes)

New App Note!AN20101 In-System Programming of P87LPC76x Microcontrollers

This application note describes how the P87LPC76x series of microcontrollers from Philips may be programmed in-circuit using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN20101 (236 Kbytes)

App NoteAN80502 In-System Programming of PIC Microcontrollers

This application note describes how the PIC series of microcontrollers from Microchip Technology Inc. may be programmed in-circuit to production standards using the dedicated JTAG/ISP connector on the Pin-Master 48 universal programmer. The programming cable, the design of the target board, and programming procedures are described.

Get AN80502 (262 Kbytes)

 

App NoteAN00201 In-System Programming of Cypress ISR Devices

This application note describes how Cypress ISR devices may be programmed in-circuit using the dedicated JTAG connector on the Pin-Master 48 universal programmer. The programming cable and programming procedures are described.

Get AN00201 (114,494 bytes)

App NoteAN00701 In-System Programming of Altera Max Devices

This application note describes how Altera Max devices may be programmed in-circuit using the dedicated JTAG connector on the Pin-Master 48 universal programmer. The programming cable and programming procedures are described.

Get AN00701 (161 Kbytes)

App NoteAN31101 In-System Programming of Atmel ATmega Devices

This application note describes how Atmel ATmega devices may be programmed in-circuit using the dedicated JTAG connector on the Pin-Master 48 universal programmer. The programming cable and programming procedures are described.

Get AN31101 (199 Kbytes)

Packet-Master User Manual

The user manual for Packet-Master USB12, USB480, USB480+ and USB500AG. Also covers the application program GraphicUSB

Get Packet-Master Manual

GraphicUSB DevKit User Manual

The user manual for the GraphicUSB DevKit option

Get GraphicUSB DevKit Manual

Pin-Master 48 User Manual

As programmer software changes so frequently we no longer supply the manual in printed form. The latest available version will be made available here and can be downloaded and printed using either A4 or Letter sized paper.

Get Pin-Master 48 Manual

System 2000 User Manual

As programmer software changes so frequently we no longer supply the manual in printed form. The latest available version will be made available here and can be downloaded and printed using either A4 or Letter sized paper.

Get System 2000 Manual

Model 200 User Manual

As programmer software changes so frequently we no longer supply the manual in printed form. The latest available version will be made available here and can be downloaded and printed using either A4 or Letter sized paper.

Get Model 200 Manual