PRODUCT DATA SHEET

Product Code	Pins on skt	Pins on Base	Wiring Code	Package	Base pitch"	Miscellaneous
AD509	56	48		SD	.6	Eject

For use on the following programmers

• Pin-Master 48

See Also: For 52 pin PLCC use AD488; for 64 pin QFP use AD574

Note:

This data sheet refers to adapters marked AD509A. The AD509 was for 68HC05B6 only. AD509A requires PROMDRIVER version 1.70 or later.

Device types

• Motorola
  • MC68HC05B6 (EEPROM only)
  • MC68HC705B16

Device package: 56 pin SDIP

Programmer socket: 48 pin DIL

Socket Specification:

Insertions:

• 5000

Replaceable: Yes

MC68HC705B16 (using Pin-Master 48)

• This microprocessor has EPROM and EEPROM, which need to be programmed. The data required to be programmed should be contained in the data file at the following locations
  • EPROM: 0020h-004Fh, 0300h-3DFEh, 3FF2h-3FFFh
  • EEPROM: 0100h-01FFh
  All checksums shown include just the locations specified above.
• The device can be locked by programming bit 0 of EEPROM address 100h to a 0. In the Pin-Master 48 this is a separate 'Special' function called 'Lock'. This allows the programmer to perform full verification after programming, and before locking. Setting this bit to 0 in the data file will NOT program the SEC bit, and will result in a verification error.
• If the device is locked, it cannot be read, or programmed in any way.
• The blank value for EPROM is 00h and for EEPROM is 0FFh.
• As the blank value is assumed, by the Pin-Master 48, to be 00h for this device, the data file must contain an 0FFh byte for every EEPROM byte which you do not wish to program. Every address not defined as EPROM or EEPROM, must be given the value of 00h if it is defined. The SEC bit must be defined as high.
• The blank check function only checks the EPROM, as the EEPROM may be programmed whatever they contain before programming. This means, of course, that the checksum of a 'blank' device may vary.
• Manual or Append Programming are available to make adjustments to EEPROM locations independently of programming EPROM.

MC68HC05B6 (using Pin-Master 48)

• This microprocessor has mask ROM (which is pre-programmed in the factory) and EEPROM, which can be programmed. The data required to be programmed should be contained in the data file at the following locations
  • EEPROM: 0100h-01FFh
• The device can be locked by programming bit 0 of EEPROM address 100h to a 0. If the device is locked, it cannot be read, or programmed in any way.
• Manual or Append Programming functions are available to make adjustments to EEPROM locations.

General: This range of package converters is manufactured in England to the highest standards by MQP Electronics. Every adapter sold is tested using an actual device. Our distributors should have no difficulty in supplying you quickly with any item. Specifications of our adapters can be found on our Web Site (www.mqp.com)

If you have any difficulty in identifying the correct converter our sales office will be pleased to advise. Our phone number is +44 1666 825 666.

Connections:

1. Uses AUT-SDIP56-01 + AUB-DIP48-01
2. A capacitor (eg 10nF) is fitted to bypass VDD supply.
3. A capacitor (eg 10nF) is fitted to bypass VPP6 supply.

In-circuit programming (MC68HC05B6 only)

The device may be programmed in circuit provided the proper conditions exist. For more information see the device data sheet. The following connections on the Pin-Master 48 JTAG socket may be used, in place of AD509 . In-circuit programming requires a good understanding of the device in question, and of the circuit containing the device.