PRODUCT DATA SHEET

AD327, AD493, AD562 and AD622

Package Converters for 16 bit Boot Block FLASH (48 pin TSOP)

Product Code	Pins on skt	Pins on Base	Wiring Code	Package	Base pitch"	Miscellaneous
AD327	48	42		TS	.6	GANG

Product Code	Pins on skt	Pins on Base	Wiring Code	Package	Base pitch"	Miscellaneous
AD493	48	42		TS	.6	GANG

Product Code	Pins on skt	Pins on Base	Wiring Code	Package	Base pitch"	Miscellaneous
AD562	48	42		TS	.6	GANG

Product Code	Pins on skt	Pins on Base	Wiring Code	Package	Base pitch"	Miscellaneous
AD622	48	42		TSR	.6	GANG, DEADBUG

Brief Introduction

AD327 was the original adapter for parts up to '800. AD493 has been introduced to program all the original devices, plus the '160 parts. It is upwards compatible with AD327.. However please note that to make use of the extended '160 capability in the S2000 gang programming system requires the MP3 module to be H/W Rev 5 or better. Also adapters are now marked AD493A and these require S2000 firmware release of 2.91 or later.

AD562 has been introduced to program all the above devices, plus the '320 parts. It is upwards compatible with AD327 and AD493, and AD562 should now be selected in preference.

AD622 is designed to enable parts in reversed package to be inserted (dead-bug) for programming.

For use on the following programmers

MQP Electronics S2000 (up to 8 converters may be fitted) NOTE: AD493, AD562 and AD622 require H/W Rev 5 of the MP3 module to program '160 parts, and firmware release 2.91 or later.
MQP Electronics Pin-Master 48

Device types (AD327, AD493, AD622 and AD562)

AMD
- 29F100T, 29F100B, 29F200T, 29F200T, 29F400T, 29F400B, 29F800T, 29F800B, 29F200, 29F400, 29F800, 29LV200, 29LV400, 29LV800

Intel
- 28F400CV-T, 28F400CV-B, 28F800CV-T, 28F800CV-B
S-T
- 29F100T, 29F100B, 29F200T, 29F200T, 29F400T, 29F400B, 29W400T, 29W400B, 29W800T, 29W800B

Further Device types, AD493, AD622 and AD562 only

AMD
- 29LV160

Intel
- 28F160B3-T, 28F160B3-B

Further Device types, AD562 (and AD622) only

AMD
- 29LV320

Intel
- 28F320B3-T, 28F320B3-B

Device package: 48 pin TSOP (Standard Orientation)

For AD622 only: 48 pin TSOP (Reverse Orientation)

Programmer socket: 42 pin DIL

Socket Specification:

Insertions:

5000

Replaceable: No

General: This range of package converters is manufactured in England to the highest standards by MQP Electronics. Every adapter sold is tested using an actual device. Our distributors should have no difficulty in supplying you quickly with any item. Specifications of our adapters can be found on our Web Site (www.mqp.com)

If you have any difficulty in identifying the correct converter our sales office will be pleased to advise. Our phone number is +44 1666 825 666.

Connections:

48 Pin TSOP Socket	Signal Name	42 Pin DIL BASE	Extras on AD493	Extras on AD562 (and AD622)
1	A15	34
2	A14	35
3	A13	36
4	A12	37
5	A11	38	a21 during special strobe*	a21 during special strobe
6	A10	39	a20 during special strobe*	a20 during special strobe
7	A9	40
8	A8	41	a19 during special strobe	a19 during special strobe
9	nc on AD327	-	latched A19 direct	latched A21 (also latched A19 direct on '160)
10	nc	-		latched A20
11	\WE	42
12	\RP	32
13	VPP	32
14	\WP	22
15	nc on AD327	-	latched A19 via 10k	latched A19 via 10k
16	A18	1	also special strobe	also special strobe
17	A17	2
18	A7	3
19	A6	4
20	A5	5
21	A4	6
22	A3	7
23	A2	8
24	A1	9
25	A0	10
26	\CE	11
27	GND	12
28	\OE	13
29	DQ0	14
30	DQ8	15
31	DQ1	16
32	DQ9	17
33	DQ2	18
34	DQ10	19
35	DQ3	20
36	DQ11	21
37	VCC	22
38	DQ4	23
39	DQ12	24
40	DQ5	25
41	DQ13	26
42	DQ6	27
43	DQ14	28
44	DQ7	29
45	DQ15 / A-1	30
46	GND	12 / 31
47	\BYTE	22
48	A16	33

* use of these reserved for future expansion

# The RoHS symbol with the # mark attached means that a RoHS compliant version of this item is available on request.